Complete set of project documentation. The composition of the design and estimate documentation

Let's consider all stages of the project in order:

Stage 1 - PP. Pre-project studies (concept, draft design)

At this stage, the concept of the future object is being developed, the main technical and economic characteristics (TEP) are being determined. The sketch determines the landing of the object on the ground, its volume-spatial solution (OPD), and the structural scheme. Also at this stage, the main engineering loads for water, heat and electricity, the so-called. load calculation.

Development Stage "PP" is not mandatory, but helps to save time and money in further design.

Stage 2 - PD. Project documentation

Unlike draft design Stage "Project"(“PD” or simply “P”) is mandatory and subject to approval by state executive authorities. According to the results of the approval of the "Project" Stage, a permit for the construction of the facility is issued. Composition and content this stage regulated by Decree of the Government of the Russian Federation No. 87 of February 16, 2008. Of course, the composition will be individual for each project, but we will try to compile the most complete list of all possible sections and subsections of the “PD” Stage:

Number	Partition code	Section name
Section 1		Explanatory note
Volume 1	OPP	Explanatory note
Volume 2	IRD	Initial permit documentation
Section 2	ROM	Scheme of planning organization land plot
Section 3	AR	Architectural solutions
Section 4		Structural and space-planning solutions
Volume 1	WP1	Reinforced concrete structures
Volume 2	WP2	Metal constructions
Volume 3	WP3	wooden structures
Volume 4	KR.R	Static calculation
Section 5		Information about engineering equipment, about networks of engineering and technical support, a list of engineering and technical measures, content technological solutions.
Subsection 1		Power supply system
Volume 1	IOS1.1	Outdoor power supply
Volume 2	IOS1.2	Power equipment
Volume 3	IOS1.3	electric lighting
Subsection 2		Water supply system
Volume 1	IOS2.1	Outdoor water supply
Volume 2	IOS2.2	domestic water supply
Subsection 3		Drainage system
Volume 1	IOS3.1	External drainage
Volume 2	IOS3.2	Internal drainage
Subsection 4		Heating, ventilation and air conditioning, heating network
Volume 1	IOS4.1	Heating and ventilation
Volume 2	IOS4.2	Heat supply
Volume 3	IOS 4.3	Individual heating point
Subsection 5		Communication networks
Volume 1	IOS5.1
Volume 2	IOS5.2
Volume 3	IOS5.3
Volume 4	IOS5.4	CCTV
Volume 5	IOS5.5	Security alarm
Volume 6	IOS5.6
Volume 7	IOS5.7	Other low current systems
Subsection 6		Gas supply system
Volume 1	IOS6.1	Outdoor gas supply
Volume 2	IOS6.2	Internal gas supply
Subsection 7		Technological solutions
Volume 1	IOS7.1	Technological solutions
Volume 2	IOS7.2
Volume 3	IOS7.3	Air supply
Volume 4	IOS7.4	Refrigeration
Volume 5	IOS7.5	Steam supply
Volume 6	IOS7.6	dust removal
Volume 7	IOS 7.7	Other technological systems
Section 6	pic	Construction organization project
Section 7	UNDER	Project for the organization of work on the demolition or dismantling of capital construction projects
Section 8
Volume 1	OOS	List of protection measures environment
Volume 2	OOS.TR	Draft technological regulations for handling construction waste at the facility
Volume 3	IEI	Engineering and environmental surveys
Section 9
Volume 1	PB1	Measures to ensure fire safety
Volume 2	PB2
Volume 3	PB3
Volume 4	PB4
Section 10	ODI	Accessibility measures for persons with disabilities
Section 10(1)	ME	Measures to ensure compliance with energy efficiency requirements and equipment requirements for buildings, structures and structures metering devices used energy resources
Section 11
Volume 1	CM1	Estimate for the construction of capital construction facilities
Volume 2	CM2	Material price monitoring
Section 12		Other documentation in cases stipulated by federal laws
Volume 1	KEO	Lighting calculations of insolation and daylight (KEO)
Volume 2	zsh	Noise and vibration protection measures. Noise impact assessment for the period of operation of the facility
Volume 3	ITM GOiChS	Engineering and technical measures of civil defense. Measures to prevent emergency situations
Volume 4	ED	Building instruction manual
Volume 5	PTA	Measures to counter terrorist acts
Volume 6	DPB	Declaration of industrial safety of hazardous production facilities

Stage 3 - RD. working documentation

Stage "RD" first of all, builders need it, since it develops design solutions in the most complete and detailed way, which were only indicated in the “PD” Stage. Unlike "P", "Working" includes drawings of nodes, axonometric diagrams and profiles of engineering networks, specifications, etc. On the other hand, at the working stage, the documentation loses some sections, the completeness of which was exhausted at the design stage (for example , POS, OOS, KEO, ITM GOiChS, etc.). As in Stage "P", the composition of the "RD" will be individual for each project, but we will try to compile the most complete list of all possible sections of the Stage "Working documentation":

Partition code	Section name
- GP	General plan
- TR	Transport facilities
- GT	General plan and transport (when GP and TR are combined)
- BP	Car roads
- pancreas	Railways
- AR	Architectural solutions
- AC	Architectural and construction solutions (when combining the Republic of Azerbaijan and the Kyrgyz Republic)
- AI	Interiors
- QOL	Constructive decisions. Reinforced concrete structures
- QOL0	Constructive decisions. Reinforced concrete structures. Foundations
- KM	Constructive decisions. Metal constructions
- KMD	Constructive decisions. Detailing metal structures
- KD	Constructive decisions. wooden structures
- KRR	Constructive decisions. Static calculation
- GR	Hydraulic Solutions
- ES	Power supply system. Outdoor power supply
- EM	Power supply system. Power equipment
- EO	Power supply system. electric lighting
- EN	Power supply system. Outdoor electric lighting
- EIS	Power supply of engineering systems
- HB	Water supply system. Outdoor networks
- NK	Water disposal system. Outdoor networks
- NVK	Water supply and sanitation system. Outdoor networks
- VC	Water supply and sanitation system. Internal networks
- HVAC	Heating, ventilation and air conditioning
- TS	Heat supply
- TM	Thermal mechanical solutions (boiler room, ITP, etc.)
- RT	Telephony, Radiofication, Telereception
- SCS	Structured cabling
- AIS	Automation of engineering systems
- ATP	Automation of technological processes
- AK	Integrated automation (when combining AIS and ATP)
- VN	CCTV
- OS	Security alarm
- ACS	Access control and accounting system
- GOS	Outdoor gas supply
- GSV	Internal gas supply
- TX	Technological solutions
- TK	Technological communications
- sun	Air supply
- XC	Refrigeration
- PS	Steam supply
- PU	dust removal
- AUPS - SOUE	Automatic fire alarm installation, Warning and evacuation control system in case of fire
- APPZ	Fire protection automation
- Fri	Special fire extinguishing (water, powder, etc.)
- SD1	Estimate for the construction of capital construction facilities
- SD2	Material price monitoring
- AZ	Anti-corrosion protection
- TI	Thermal insulation of equipment and pipelines

GOST R 21.1101-2013 System project documentation:

4.2. working documentation
4.2.1. The composition of the working documentation transferred to the customer includes:
- working drawings intended for the production of construction and installation work;
- attached documents developed in addition to the working drawings of the main set.
4.2.2. The main sets of working drawings include general data on working drawings, drawings and diagrams provided for by the relevant standards of the Design Documentation System for Construction (hereinafter referred to as SPDS).
...
4.2.6. The attached documents include:
- working documentation for building products;
- sketch drawings general types non-standard products made in accordance with GOST 21.114;
- specification of equipment, products and materials, carried out in accordance with GOST 21.110;
- questionnaires and dimensional drawings, performed in accordance with the data of equipment manufacturers;
- local estimate according to the forms;
- other documents stipulated by the relevant SPDS standards.
The specific composition of the attached documents and the need for their implementation are established by the relevant SPDS standards and the design assignment.
...
4.2.8. In working drawings, it is allowed to use standard building structures, products and assemblies by referring to documents containing working drawings of these structures and products. Reference documents include:
- drawings of typical structures, products and assemblies;
- standards, which include drawings intended for the manufacture of products.
Reference documents are not included in the working documentation transferred to the customer. The design organization, if necessary, transfers them to the customer under a separate agreement.

SNiP 11-01-95 Composition of working documentation:

5.1. The composition of the working documentation for the construction of enterprises, buildings and structures is determined by the relevant state standards SPDS and specified by the customer and the designer in the agreement (contract) for the design.

5.2. State, industry and republican standards, as well as drawings of typical structures, products and assemblies, to which there are references in the working drawings, are not part of the working documentation and can be transferred by the designer to the customer, if this is stipulated in the contract.

The implementation of construction projects requires the development of special documentation, in accordance with which the work of specialists should be carried out. Its structure, as well as the procedure for approval, are determined by law - at the level of federal regulations. Main element of the corresponding set of sources - project documentation. In some cases, it can be supplemented by working, as well as specifications. What are the features of the development of project documentation in construction? What are the main sources of law governing its application?

What is project documentation?

Under project documentation (or design estimates) it is customary to understand a set of sources, which may include both textual and graphic materials, designed to determine the lists of architectural, technological, constructive, as well as engineering solutions used in the implementation of a construction project.

Depending on the complexity of the tasks facing the firm, the structure of the relevant documentation may vary. It depends on its composition, which specific specialists will be involved in the development of these sources.

The role of design documentation in construction

Actually, what is the design estimate documentation for? Its main role lies primarily in the regulation of the process of implementing a construction project. In addition, the preparation of relevant documentation is a legal requirement. Without it, it is impossible to accept the constructed property for operation. Similarly, design estimates are needed for the reconstruction or redevelopment of buildings and structures.

Thus, the sources under consideration are needed both in terms of legal requirements and for the implementation of the work itself as an objectively necessary source of data that allows you to build a building or structure that meets the established quality criteria, as well as within the costs determined by the project participants.

The project documentation system is a set of sources, in fact, reflecting the general understanding of the customer and the developer of the project concept, as well as establishing the procedure for the uninterrupted and prompt supply of various elements of the construction infrastructure. The important role of the sources under consideration predetermines the need to involve the most qualified specialists in their development, as well as following special algorithms.

So, the relevant work should be carried out only by those organizations that have to carry out work related to the preparation of documentation, which in question. Let us consider in more detail who can carry out its development.

Who develops project documentation?

The developer himself or a competent person who is involved by him or the customer can create design and estimate documentation. Sometimes an individual under a contract. For example, it could be an experienced engineer.

The person who is responsible for the preparation of the documentation in question also coordinates the work necessary to create the relevant sources. In addition, he is responsible for the quality of documentation, as well as its compliance with technical regulations. The preparation of project documentation may in some cases be accompanied by the delegation of a number of developer functions to other persons who have the necessary competence.

The customer provides the developer with a number of relevant sources:

Urban planning plan for the site or a planning project for the territory that is supposed to be used as part of the construction project;

A document reflecting the results of engineering surveys or, if they are not ready, a task for their implementation;

Specifications, if the functioning of the construction object requires a technological connection.

Let's consider what requirements exist for the composition of sections of the relevant documentation, which is used in the framework of construction projects, in solving problems of reconstruction and overhaul of various buildings and structures.

Requirements for the structure of project documentation

The main source of law, which prescribes what requirements the project documentation of an object must meet, is the Town Planning Code of the Russian Federation. It also says that the requirements for the sources under consideration are established by the government of the Russian Federation. In practice, the composition of sections of project documentation intended for construction, reconstruction and overhaul is determined mainly in Decree of the Government of the Russian Federation No. 87, adopted on February 16, 2008. In addition, the criteria established by this source of law in many cases correlate with the provisions of the Town Planning Code.

They have a production purpose;

Characterized by non-production purpose;

Are linear.

Let us now consider how Decree No. 87 determines, in fact, the composition of project documentation. Compliance with these requirements is a key condition for the successful development of these sources.

The composition of the project documentation

In accordance with Decree No. 87, a correctly drawn up project documentation includes 12 sections. Their structure contains:

Explanatory note;

Section with the layout plan of the land plot;

A document reflecting the list of architectural solutions;

Section on constructive, as well as space-planning building solutions;

A document reflecting information about the engineering infrastructure, supply networks, lists of technical measures, the content of various technological solutions;

Section explaining the essence of the construction organization project;

A document reflecting the essence of the project for the organization of those works that are associated with the demolition of capital construction facilities, if this procedure is required;

Section presenting a list of activities related to ensuring environmental protection;

Section on activities aimed at providing access for people with disabilities;

A document reflecting the list of measures aimed at improving the energy efficiency of facilities;

Estimate reflecting data on objects;

Other documents, the inclusion of which in the design and estimate documentation is required by law.

It can be noted that the section that reflects information about the engineering infrastructure includes several subsections, namely, sources that disclose data on water supply, sanitation, heating, ventilation, air conditioning, gas supply, communications.

Also, in the structure of the section under consideration, there should be a subsection that provides information about technological solutions. It should be noted that in accordance with the Urban Planning Code, correctly drawn up project documentation includes sections presented in a slightly different structure. In particular, it involves the inclusion in the sources under consideration of a section reflecting information about collateral required level safe operation of construction sites, which, in turn, is not provided for by Decree No. 87.

If the project documentation requires the inclusion of other sections that are not defined as its mandatory elements in the legislation, then their list is fixed in agreements between the developer of the relevant sources and the customer. It can be noted that some of those sections of the documentation that are defined by law must be included in it only if the construction project is implemented at the expense of budget organizations. Their specific list is given in Decree No. 87.

Can be compiled for individual stages of implementation construction works project documentation? Documentation, the project described in it, indeed, can be considered in the context of specific periods of the construction plan. In this case, the need to develop a separate group of sources for each stage is fixed in the task for creating the project. At the same time, this procedure is subject to justification by special calculations, which confirm the possibility of the practical implementation of certain design decisions as part of the implementation of the construction project in stages.

In addition, the documentation used in specific periods of construction is developed to the extent prescribed. Its structure in terms of the main elements, as well as the presence of sections, must comply with the requirements established in Decree No. 87.

Purpose of working documentation

So, we have considered what a well-prepared project documentation includes, as well as its main features. However, in practice, this set of sources, in order to regulate construction work, as a rule, is also supplemented by another type of documentation - working documentation. It will be useful to study its features.

It can be noted that Regulation No. 87 does not unequivocally regulate the order in which the working component of the sources for the project implementation should be developed. The relevant legal act establishes that, like the project documentation, it includes both text and graphic documents. For example, drawings, various specifications.

In principle, design and working documentation can be created simultaneously. The composition and structure of the latter are generally determined by the customer or the developer, depending on the detailing of certain solutions given in the project documentation. The corresponding parameters can be fixed in the task sent to the developer of the considered sources.

The main elements of working documentation are drawings, specifications and other supplementary documents. Based on them, the implementation of those decisions that are provided for by the project is carried out.

Specifications as part of construction documentation

The next most important type of source that can complement project documentation is specifications. It will be useful to consider their specifics. To a certain extent, the application of technical conditions is also regulated by Decree No. 87. Thus, in the relevant legal act it is indicated that they are developed and approved if:

The implementation of design documentation requires a larger list of requirements that reflect the reliability and safety of structures, relative to the list established by regulatory enactments;

The relevant requirements are not defined in the regulations.

Specifications must be developed in the manner prescribed by law. In practice, it is determined by the competent department - the Ministry of Construction and Housing and Public Utilities of the Russian Federation in agreement with other federal bodies of the Russian Federation.

Thus, the design documentation includes working documentation in the cases provided for by law, as well as in the presence of certain agreements between the customer and the developer of the relevant sources. In some cases, it is supplemented by technical conditions, which are also created in the manner determined by the legislator.

The structure of project documentation according to Decree No. 87

In accordance with the provisions of Decree No. 87, the preparation of project documentation involves the inclusion of text and graphic elements in it. The first should reflect:

Information about the construction object;

Descriptions of various solutions, in particular technical ones;

Calculations that justify the decisions made in the development of the project.

The graphic part of the project documentation clearly displays the relevant solutions. For this can be used:

Blueprints;

Graphic schemes;

Other Required documents presented in graphical form.

The preparation of project documentation within the framework of the acquisition of both types of elements, both textual and graphic, must be carried out in compliance with the requirements of the legislation on state secrets by the organization that performs the relevant work. The way in which certain elements of the documentation in question should be drawn up is regulated by the standards established by the Ministry of Construction and Housing and Public Utilities of the Russian Federation.

Documentation review

So, we have considered that the design and estimate documentation includes, in accordance with what rules of law it is drawn up. It will also be useful to study one of critical aspects its application is the state examination of these sources.

The procedure in question is carried out in order to create construction objects in accordance with the requirements of the legislation in force in various fields, including those aimed at guaranteeing the observance of the rights of citizens and organizations in various legal relations. must undergo an examination in accordance with the Town Planning Code of the Russian Federation, as well as Federal Law No. 337, adopted on November 28, 2011. The corresponding procedure is carried out by the competent state authorities.

However, in preparation for construction firm can turn to the services of private structures that can provide support for the examination in question. What is the nature of this service?

Accompanying the state examination of construction documentation

Accompanying the examination of project documentation includes most often:

Conducting a non-state examination in accordance with criteria generally consistent with those that guide the competent departments;

Audit of specific sections of the documentation to identify gaps in them, determine the degree of compliance established requirements legislation;

preparation necessary materials for the transfer of documents to government agency who conducts the examination.

Many firms also offer their customers advisory support directly during the period of their interaction with departments that conduct state examination of documentation. Experts recommend contacting companies that are ready to provide both legal, organizational and consulting support for the development of project documentation. In all the mentioned aspects, the assistance of experienced specialists can be useful for an enterprise implementing a construction project.

Cost calculation

List of sections of design documentation for capital construction facilities for industrial and non-industrial purposes

(houses, warehouses, administrative buildings, shopping centers, business centers, etc.)

GPU

Lease contract

Cadastral plan

land contract

Specifications

SRO designers

Project documentation

1. Explanatory note

2. Scheme of the planning organization of the land plot

3.Architectural solutions

4.Constructive and space-planning solutions

5. Information about engineering equipment, engineering and technical support networks, a list of engineering and technical measures, the content of technological solutions

5.1. Power supply system

5.2. Water supply system

5.3. Drainage system

5.4. Heating, ventilation and air conditioning, heating networks

5.5. Communication networks

5.6. Gas supply system

5.7. Technological solutions

6. Construction organization project

7. Project for the organization of work on the demolition or dismantling of capital construction objects "(performed if necessary, demolition (dismantling) of an object or part of a capital construction object)

8.List of measures for environmental protection

9. Measures to ensure fire safety

10.Measures to ensure access for persons with disabilities

10(1). Measures to ensure compliance with the requirements of energy efficiency and the requirements for equipping buildings, structures and structures with metering devices for the energy resources used

11. Estimate for the construction of capital construction projects

12. Other documentation in cases provided for federal laws

12.1. Safe operation buildings and structures

12.2. civil defense and emergency situations

12.3. Anti-terrorist measures

12.4. Traffic management

Geotechnical

Engineering and geodetic

Engineering and environmental

List of design documentation sections for linear capital construction projects

(gas pipelines, water pressure units, electricity networks, etc.)

Initial permit documentation

GPU

Lease contract

Cadastral plan

land contract

Specifications

SRO designers

Project documentation

1. Explanatory note

2. Project of the right of way

3. Technological and design solutions for a linear object. Artificial constructions

4. Buildings, structures and structures included in the infrastructure of a linear facility

5. Construction organization project

6. Project for the organization of work on the demolition (dismantling) of a linear facility

7.Measures for environmental protection

8. Measures to ensure fire safety

9. Estimate for construction

10. Other documentation in cases stipulated by federal laws

Documents based on the results of engineering surveys

Geotechnical

Engineering and geodetic

Engineering and environmental

Cost calculation

To develop a project for new construction, renovation or overhaul required to develop project documentation. The composition of project documentation is regulated by Decree No. 87 "On the composition of sections of project documentation and requirements for their content."

All projects can be divided into 2 categories: capital construction facilities and linear facilities.

Capital construction objects include various buildings and structures that have above-ground and (or) underground parts, including premises, engineering and technical support networks and engineering and technical support systems and intended for living and (or) activities of people, locating production, storage of products or keeping animals.

Capital construction projects do not include temporary structures. Temporary buildings do not require an examination at all, therefore, there are no requirements for the composition of project documentation.

Temporary buildings and the capital construction option have external similar features, while, according to Urban Planning Code Russia defined technical differences of objects:

1. The object of the capital characteristics of the construction is tied to a permanent foundation, while there is always a link to the land. A temporary building may not have a foundation.
2. The capital object involves the collection permits for full operation, while the temporary building has a minimum set of documents for permission to operate.
3. The minimum service life for an object of category CS (capital construction) is 25 years, and may be more than 100 years. Temporary buildings should be used for no more than 25 years, with a mandatory condition for demolition.
4. The capital object cannot be demolished, transferred to another place, with the exception of a number of provisions of the urban planning code.
5. The object of completed construction works involves the use of property rights with registration in the Rosreestr; for temporary buildings, restrictive permissive functions of property rights are presented.

Linear objects include: power lines, communication lines (including linear cable structures), pipelines, roads, railway lines, bridges, overpasses, pedestrian crossings and other similar structures.

If a linear facility contains buildings and structures that are related to capital construction, then a project for a linear structure is developed in accordance with the list of sections for a linear structure and separately projects for buildings and structures in accordance with the requirements for sections on capital construction. Section 4 of the linear facility provides a list, characteristics and links to building designs that are part of the infrastructure of the linear facility.

The composition of the design documentation for the capital construction object:

Section 2 "Scheme of the planning organization of the land plot" (PZU)

Section 3 "Architectural Solutions" (AR)

Section 4 "Constructive and space-planning solutions" (KR)

Section 5 "Information on engineering equipment, on networks of engineering and technical support, a list of engineering and technical measures, the content of technological solutions"

This section consists of subsections:

a) subsection "Power supply system" (IOS1);

b) subsection "Water supply system" (IOS2);

c) subsection "Water disposal system" (IOS3);

d) subsection "Heating, ventilation and air conditioning, heat networks" (IOS4);

e) subsection "Communication networks" (IOS5);

f) subsection "Gas supply system" (IOS6);

g) subsection "Technological solutions" (IOS7).

Section 6 "Construction Organization Project" (POS)

Section 7 "Project for the organization of work on the demolition or dismantling of capital construction objects" (POD)

Section 8 "List of Measures for Environmental Protection" (LEP)

Section 9 "Measures to ensure fire safety" (PB)

Section 10 Accessibility Measures for Persons with Disabilities (ODA)

Section 10(1) "Measures to ensure compliance with energy efficiency requirements and the requirements for equipping buildings, structures and structures with metering devices for the energy resources used" (EE)

Section 11 "Estimates for the construction of capital construction facilities" (SM)

Section 12 "Other documentation in cases provided for by federal laws"

The composition of design documentation for linear facilities:

Section 1 "Explanatory Note" (PZ)

Section 2 "Project of the right of way" (PPO)

Section 3 “Technological and design solutions for a linear facility. Artificial Structures (TKR)

Section 4 "Buildings, structures and structures included in the infrastructure of a linear facility" (ILO)

Section 5 "Construction Organization Project" (POS)

Section 6 "Project for the organization of work on the demolition (dismantling) of a linear facility" (POD)

Section 7 "Measures for the protection of the environment" (EP)

Section 8 "Measures to ensure fire safety" (PB)

Section 9 Construction Estimate (CM)

Section 10 "Other documentation in cases provided for by federal laws"

If any of the sections is not being developed, then this section is still written as part of the project, but we add the inscription “Not developed” to the note. The section numbering does not change.

For example, Section 7 “Design for the organization of work on the demolition or dismantling of capital construction objects” is not always required and we do not develop it, but the numbering of sections does not change because of this, the following section Section 8 “List of environmental protection measures” will remain section 8.

A section may contain subsections, such as in Section 5. In larger projects, subsections may also be subdivided. Parts are divided into books.

2345-IOS4.1.1 - Section 5. Information about engineering equipment, engineering networks, a list of engineering measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, heating networks. Part 1. Heating, ventilation and air conditioning. Book 1. Major Decisions.

2345-IOS4.1.2 - Section 5. Information about engineering equipment, engineering networks, a list of engineering measures, the content of technological solutions. Subsection 4. Heating, ventilation and air conditioning, heating networks. Part 1. Heating, ventilation and air conditioning. Book 2. Automation systems for heating, ventilation and air conditioning

Each section, subsection, part and, if necessary, book, compiled in a volume, as well as each text and graphic document included in a volume, is assigned an independent designation, which is indicated on the cover, title page and/or in the main inscription, as well as in the headers and footers of text documents executed without main inscriptions.

The section "Other documentation in cases provided for by federal laws" contains sections that are not included in the main list, but are necessary in the project, for example:

• Declaration of industrial safety of hazardous production facilities (PB HPO);
• List of events for civil defense, preventive measures emergencies natural and man-made nature (GOChS)
• Technological regulations for waste management
• Security and protection deratization system (OZDS)
• Transport security
• Survey reports

and other sections that are provided for by federal laws or the design assignment from the Customer.

All documents are assigned their own code, in accordance with the current design organization system. The cipher includes, for example, the number of the agreement (contract) and / or the code of the construction object (numeric, alphabetic or alphanumeric). It is allowed to include other codes used in CAD and EDMS in the basic designation.

If the section is divided into parts, then the part designation is made up of the section designation, to which the part number is added.

2345-PZ - Section 1. Explanatory note.

2345-PZU1 - Section 2. Scheme of the planning organization of the land plot. Part 1. General information.

2345-PZU2 - Section 2. Scheme of the planning organization of the land plot. Part 2. Decisions on internal railway transport. If the part is divided into books, then the designation of the book is made up of the designation of the part, to which the number of the book is added through a dot.

Requirements for the preparation of project documentation are set out in GOST R 21.1101-2013 SPDS. Basic requirements for design and working documentation

Volumes are completed in the following order:

— cover;

- title page;

- statement "Composition of design documentation" (It is allowed not to include the statement "Composition of design documentation" in each volume, but to complete it with a separate volume);

- text part;

— graphic part (drawings and diagrams).

The number of sheets included in the volume is determined from the need to ensure the convenience of work, as a rule, not more than 300 sheets of A4 format according to GOST 2.301 or an equivalent number of sheets of other formats.

The title page is performed in accordance with Form 12 (Appendix H GOST R 21.1101-2013).

The following details are on the cover:

- field 5 - the name of the capital construction object and, if necessary, the type of construction. The name of the construction object on the cover must correspond to the information given in columns 2 and 3 of the main inscription (see Appendix G);

- field 9 - volume number according to the statement "Composition of design documentation" or "Composition reporting documentation according to the results of engineering surveys” (if any);

- field 10 - year of issue of the document;

- field 11 - to place the table of registration of changes in the form 11 of Appendix M (if necessary).

The title page is performed according to form 13 (Appendix P GOST R 21.1101-2013).

The title page contains the following details:

- field 1 - abbreviated, and in its absence - the full name of the parent organization (if any); usually indicated for government organizations;

- field 2 - logo (optional), full name of the organization that prepared the document;

- field 3 - the number and date of issue of the certificate of admission to the relevant types of work (preparation of project documentation or surveys) that affect the safety of the capital construction object;

- field 4 - short name of the customer organization (if necessary). The name is indicated in the form: “Customer - name of the customer organization”;

- field 5 - the name of the capital construction object and, if necessary, the type of construction. The name of the construction object on the title page must correspond to the information given in columns 2 and 3 of the main inscription (see Appendix G);

- field 6 - type of documentation (if necessary);

- field 7 - the name of the document;

- field 8 - document designation;

- field 9 - volume number according to the list "Composition of design documentation" or "Composition of reporting documentation for engineering surveys" (if any);

- field 10 - positions of persons responsible for the development of the document;

- field 11 - signatures of the persons indicated in field 10, performed in accordance with GOST R 6.30. This field is also affixed with a certifying imprint of the seal of the organization that prepared the document;

- field 12 - initials and surnames of the persons indicated in field 10;

- field 13 - year of issue of the document;

- field 14 - for placing a table for registering changes in form 11 of Appendix M (if necessary);

- field 15 - for additional columns of the main inscription in accordance with Appendix G. It is allowed to present the information contained in these columns in a different form in accordance with the requirements established in the standards of the organization.

The title may also be in A3 format, if the document itself has such a format.